How do I change my IP address?

Updated: 05/16/2020 by Calculator Promise

IP address

On the Internet, your IP address is similar to your physical address in existent life. It uniquely identifies where y'all are so that information can be sent to you. Similar to your current location, your IP accost can alter in certain situations. If y'all want to change your IP accost, follow the instructions on this page.

The basics

Before reading any of the below information, you need to be aware of some network basics.

  1. Know the departure betwixt a static IP accost and a dynamic IP address. See each link for boosted data about each of these terms.
  2. When on the Internet, it is upwardly to your ISP (Internet service provider) to assign and give you your network accost seen by the Net. When on a LAN (local area network) or WAN (wide area network), the home or corporate router assigns the IP addresses.
  3. If you're planning on designating or using a static IP address, be aware of how IP address ranges are handled and exist familiar with the netmask. See each of these links for additional information.

Changing your Cyberspace IP address

Punch-up modem users

When connecting to the Internet over a dial-up modem, your Internet access provider assigns your figurer a different IP address each fourth dimension you connect. If you lot want to modify your IP address, effort disconnecting and reconnecting. If yous're assigned the same address, disconnect for a few minutes and reconnect.

Broadband users

Broadband service providers assign your computer or abode network a static IP address. If you're connected to a broadband network and need to change your IP address, follow the steps below.

Disconnect ability to the broadband modem

Getting a new IP address may be as simple as disconnecting the power to your broadband modem. Disconnect the power from the modem and leave it disconnected for a few minutes. If you lot have a network router connected to the modem, we as well advise disconnecting the ability to the router to reset the IP.

Release the IP accost assigned to the router

If disconnecting the power to the modem and router did not work, it may still exist saved in your router configuration. Try releasing and renewing the IP accost for the router. Steps on how to do this can vary depending on the router. Nonetheless, it's often done through the Status or set up in the router setup.

  • How practice I adjust the settings of my home router?

Exit it asunder overnight

If the higher up suggestions don't work, disconnect the modem and router (if applicable) ability and get out it disconnected overnight. Leaving it disconnected may bespeak to the ISP that the IP is no longer in use and assign it to a dissimilar client.

Contact the Internet access provider

If none of the above suggestions help, your ISP may foreclose a new IP address from being assigned unless it's abased for days. In this state of affairs, it'southward usually easiest to contact the Internet access provider to get the IP address changed.

Irresolute your home network IP address

To alter or specify the IP address of your computer equally it appears on your LAN (local surface area network), follow the steps beneath. Keep in mind, if you're connecting to the Internet with a broadband connection, adjusting your network settings may cause issues with your broadband connectedness. Finally, if your home network uses a router, it could be assigning your calculator dynamic IP addresses, and specifying a static IP address may cause issues.

Windows Vista and afterwards

  1. Open the Control Panel.
  2. Click the Network and Sharing Center icon.
  3. In the View your active networks section, click the Local Surface area Connection or Ethernet link, or click the Internet connexion proper name side by side to Connections.
  4. On the Local Expanse Connection or Ethernet Status window, click the Properties button.
  5. In the Backdrop window, select the Internet Protocol version 6 (TCP/IPv6) or Internet Protocol version 4 (TCP/IPv4) connection and click the Properties push button. The connection yous select depends on the type of Internet protocol in use for your Internet or network connection.
  6. In the Internet Protocol Properties window, select the Use the following IP address pick if non already selected. Specify the new IP address yous want to use. Also, specify the subnet mask and default gateway.

Windows XP and before

  1. Open the Command Panel.
  2. Right-click My Network Places or Network Neighborhood, and select Backdrop.
  3. Right-click Local Surface area Connection and select Properties.
  4. Click Internet Protocol (TCP/IP) and click the Properties button. If this is non nowadays, you lot need to install the Internet Protocol (TCP/IP) protocol.
  5. In the Net Protocol (TCP/IP) Properties window, select the Use the following IP address option if not already selected and specify the new IP address you want to use. Likewise, specify the subnet mask and default gateway.

Windows command prompt

You lot can change a computer's IP address through the command prompt by following the steps below.

  1. Open the Windows command prompt.
  2. Type netsh to start the netsh utility.
  3. To change the IP address, you need to specify not only the new IP address merely as well the subnet mask and default gateway. Use the control construction below.
interface ip set address name="[connexion name]" static [IP address] [Subnet Mask] [Default Gateway]

In the above command structure, replace [connexion name] with the proper noun of the network connexion that you want to set the new IP address. The most common network connection names are "Local Surface area Connection" or "Wi-Fi." Supplant [IP address] with the new IP address you lot want to use, then replace [Subnet Mask] with the correct subnet mask address and [Default Gateway] with the correct default gateway accost.

interface ip set up accost proper name="Local Area Connection" static 192.168.110.235 255.255.255.0 192.168.0.1

The above example command would change the IP address of the Local Expanse Connection network connection to 192.168.110.235. It would likewise set the Subnet Mask to 255.255.255.0 and the Default Gateway to 192.168.0.1.

Linux users

The below information is for how to specify and conform your network settings through the command prompt. Changing your network settings require root admission.

  1. Go to the shell.
  2. Move to the /etc/sysconfig/network directory.
  3. Edit the interfaces file and conform your network settings in this file.

Can someone else change my IP address?

Someone who's outside your home network and does non have admission to your network router cannot change your IP address. Exercise not be concerned about your computer'south security if your IP accost has inverse. It'southward more than probable that it's normal behavior than an attack.